This is the adventure and volunteerism log for Matthew Dexter Edmonds, aka "Treeman." Aside from Blogger comments, contact information is listed on Google+. And all places mentioned in this log are in the State of Ohio in United States of America unless otherwise stated. "The Wayne" = the Wayne NF.
Also, the motorhome mentioned is a 25ft, 1988 Itasca Sundancer, Model IF424RC with a Ford Econoline cutaway unless otherwise stated. It runs a 351 Windsor EFI V8 engine.
Search This Blog
Showing posts with label wiring. Show all posts
Showing posts with label wiring. Show all posts
2019/10/01
Gauge Lights Work
I finished wiring my voltmeter, oil pressure, water temperature and tachometer to the power system of my 1987 Chevy G20 Sportvan. I tested the gauge lights, I got the power from the headlight switch to work, but the only thing that I got wrong was I didn't do it to the dimer switch. Oh well. I'm happy. I did turn the key to the accessory position and got a low voltage reading. The instructions for it come with troubleshooting tips. I didn't want to turn the engine over yet because I still have to install the lines for three of the gauges to the engine.
2019/09/29
1987 Chevy G20 Van Ignition Wire
On my 1987 Chevrolet G20 Sportvan, the positive wire that only comes on when the ignition key is turned to accessory, or on is yellow in color and I found mine under the steering column. I had to remove the dashboard underside to get to it.
2019/08/30
Stereo Wired
When I had the stereo head unit installed in my former 2008 Chevy HHR, I bought it from Best Buy and had Geek Squad install it. They said that they had to dismount the entire dashboard to get to it and I can tell you that at the time, that was way over my head. But the HHR had existing stock wiring for it.
My stripped down 1987 Chevy G20 Sportvan didn't. It has an aftermarket fuse block and the radio fuse wasn't wired to it. I ended up using a device that I inserted into my "Gauges" fuse slot. It's kind of a like a SIM converter on a computer that back in the day, could turn a mother board with a 4MB total RAM slots and make it an 8MB. This thing had two female fuse slots. One was for the 20 amp fuse for the gauges and the other was for a postive wire extending out if it. The second one could only hold a up to a 10 amp fuse, which was just enough for the stereo.
I got it wired like I mentioned before. The gauges fuse port in the block was the only one that was wired to the ignition. That became a problem later on. But I got the stereo and rear speakers wired up. I didn't do the fronts because taking apart the dashboard entailed dismounting the speedometer cable and I wasn't prepared to do that. At this point, I believe that it has to be dismounted from the transmission. Normally when it comes to doing something I don't know, I study the Haynes manual the night before I do something like this. That way I get familiar with it in theory before application.
I wanted to move on to the aftermarket gauges. But they too need a power source that is switched to the ignition. Had that fuse been able to handle more than 10 amps, I could have done everything on the same positive wire. But now, I have two choices. I don't know the make and model of the aftermarket fuse block. So, I can either unbolt it and go exploring, or I can attach a switch to it, which means that I would have had to bore another hole in the dashboard that I wasn't prepared to do.
So, I stopped for the day. I don't know when I'll get back to it? The right rear speaker box has a short in its speaker wire inputs.
The stereo wiring was a bunch to stuff in. I had to make sure that it missed the seals for the interior engine hump cover, otherwise known as a "dog house."
My stripped down 1987 Chevy G20 Sportvan didn't. It has an aftermarket fuse block and the radio fuse wasn't wired to it. I ended up using a device that I inserted into my "Gauges" fuse slot. It's kind of a like a SIM converter on a computer that back in the day, could turn a mother board with a 4MB total RAM slots and make it an 8MB. This thing had two female fuse slots. One was for the 20 amp fuse for the gauges and the other was for a postive wire extending out if it. The second one could only hold a up to a 10 amp fuse, which was just enough for the stereo.
I got it wired like I mentioned before. The gauges fuse port in the block was the only one that was wired to the ignition. That became a problem later on. But I got the stereo and rear speakers wired up. I didn't do the fronts because taking apart the dashboard entailed dismounting the speedometer cable and I wasn't prepared to do that. At this point, I believe that it has to be dismounted from the transmission. Normally when it comes to doing something I don't know, I study the Haynes manual the night before I do something like this. That way I get familiar with it in theory before application.
I wanted to move on to the aftermarket gauges. But they too need a power source that is switched to the ignition. Had that fuse been able to handle more than 10 amps, I could have done everything on the same positive wire. But now, I have two choices. I don't know the make and model of the aftermarket fuse block. So, I can either unbolt it and go exploring, or I can attach a switch to it, which means that I would have had to bore another hole in the dashboard that I wasn't prepared to do.
So, I stopped for the day. I don't know when I'll get back to it? The right rear speaker box has a short in its speaker wire inputs.
The stereo wiring was a bunch to stuff in. I had to make sure that it missed the seals for the interior engine hump cover, otherwise known as a "dog house."
2019/08/29
Rear Speaker Wires Routed
I got the rear speaker wire routed in my 1987 Chevy G20 Sportvan. My interior is stripped down to the metal, so I drilled holes in the upper sides and on one of the roof supports for zip ties. I had to reroute my original plan so that the speaker wires didn't run parallel with the interior light and a custom 12V primary wire. Those power wires run along the left side, while the speakers had to go right. The trick now is to figure out how to route the wires in the passenger's side foot well to avoid the primary wire supplying power to my custom, dedicated front 12V power port? Under the dash, I'll have to keep the wires somewhat slack to install the head unit and get it back out should I need to?
Tomorrow is a big day. The primary 12V wire is already routed under the head unit, so that's where I'm going to get the head units "always on" power for it's clock since that wire goes directly to the battery. I'm not sure if I'll have to fuse it?
Now, I have a fuse splitter for the block. I don't have to go behind it and find out what's what? I'm going to run primary power for 5 components off that one line. I have a stereo head unit, tachometer, oil pressure, temperature gauges and a voltmeter. All the components will need to be hooked to the light switch. Then a few grounds will have to be run.
I'm looking forward to installing the water gauge and tachometer. I have to drill quite a hole to get the temperature sensor out of the firewall.
Tomorrow is a big day. The primary 12V wire is already routed under the head unit, so that's where I'm going to get the head units "always on" power for it's clock since that wire goes directly to the battery. I'm not sure if I'll have to fuse it?
Now, I have a fuse splitter for the block. I don't have to go behind it and find out what's what? I'm going to run primary power for 5 components off that one line. I have a stereo head unit, tachometer, oil pressure, temperature gauges and a voltmeter. All the components will need to be hooked to the light switch. Then a few grounds will have to be run.
I'm looking forward to installing the water gauge and tachometer. I have to drill quite a hole to get the temperature sensor out of the firewall.
2018/03/31
On My Plate Now
So what's on my plate now? Well, the things that come to mind are setting up my data that I've generated at home port to go on the road now. I've actually got two letters requesting maintenance help from the Boy Scouts of America on National Trails Day. The website is on hold until I can talk to the BTA at TrailFest later next month. The trail manuals need a little proofreading. That's something that I'd rather do at a local coffee shop. Some of the events that I have tentatively scheduled.
The motorhome's tile floor is probably going in on Tuesday. I believe that my mechanic has finished? But there are some vanity items that have yet to be put up. I have to diagnose an electrical problem. The dashboard, turn signals and forward marker lights don't work. All at once, that sounds like a fuse to me? But I might have a wiring problem? And if so, there's a three way junction at the driver's side marker light that I may have miswired? I believe that the rears are working, but I have to check again.
I checked the breaker switches and so far, that weak one seems like it's suddenly better. But I can't find my replacement breaker switch that I'm sure that I purchased, so maybe I did it already. The converter's face place was never secured and from what I see, it's because one of the switches is rocked out. If I can get it in place, then it will need some mounting screws. This is the sort of thing that I like doing with the motorhome in Lowe's or Home Depot's parking lot. Because if you get the wrong screws, you don't have to go far to get new ones. And I plan on having the auxiliary batteries replaced first thing tomorrow.
The caulking on the front windows was one of the last things that I did. But it didn't hold up and caused a slight leak. Considering that I'm going to move it on Tuesday, I'm going to hold off until I get it back into storage that day to re-caulk those, then put a tarp over the nose for a few days to let it properly hue.
The motorhome's tile floor is probably going in on Tuesday. I believe that my mechanic has finished? But there are some vanity items that have yet to be put up. I have to diagnose an electrical problem. The dashboard, turn signals and forward marker lights don't work. All at once, that sounds like a fuse to me? But I might have a wiring problem? And if so, there's a three way junction at the driver's side marker light that I may have miswired? I believe that the rears are working, but I have to check again.
I checked the breaker switches and so far, that weak one seems like it's suddenly better. But I can't find my replacement breaker switch that I'm sure that I purchased, so maybe I did it already. The converter's face place was never secured and from what I see, it's because one of the switches is rocked out. If I can get it in place, then it will need some mounting screws. This is the sort of thing that I like doing with the motorhome in Lowe's or Home Depot's parking lot. Because if you get the wrong screws, you don't have to go far to get new ones. And I plan on having the auxiliary batteries replaced first thing tomorrow.
The caulking on the front windows was one of the last things that I did. But it didn't hold up and caused a slight leak. Considering that I'm going to move it on Tuesday, I'm going to hold off until I get it back into storage that day to re-caulk those, then put a tarp over the nose for a few days to let it properly hue.
2018/02/10
Two Wi-Fi/ Cellular Signal Booster Antennas and Wiring
I found an SMA splitter. If I'm right, that means that I can have two Wi-Fi/ cellular signal booster antennas mounted on the mirror bars. I'll now have to purchase the second antenna and about 20 feet of SMA cable to go from the passenger's side cab door to the table overhead compartment in the chassis on the driver's side. I'll probably get it at Micro Center when I purchase the second antenna.
With the brakes out of the way, we're on to more cosmetic things in the chassis. Since we're going to tear apart a lot, this is the point where we'll have access to the analog coax cables and get to replace them. There three ports in the motorhome. One is outside to jack in cable TV. The other two are inside. One is above the table and the other is in the bedroom area. The SMA cables will have simiar routing, so we might as well do it then.
With the brakes out of the way, we're on to more cosmetic things in the chassis. Since we're going to tear apart a lot, this is the point where we'll have access to the analog coax cables and get to replace them. There three ports in the motorhome. One is outside to jack in cable TV. The other two are inside. One is above the table and the other is in the bedroom area. The SMA cables will have simiar routing, so we might as well do it then.
2016/10/07
Log 2016100701
I got a few things done today.
- Spare tire cover installed
The stock one was plastic with a wider outer diameter and it interfered with my hitch mounted bicycle rack.
- Frayed 12 gauge wire repaired temporarily
It's brown and I found out that was the main wire to my brake and running lights. I realized during the repair that I didn't have any extra 12 gauge wire. But I pulled it taunt enough to connect it with a blue cylinder.
- I purchased a laptop safe today, but in placing it in the motorhome, it ended up being larger than I wanted and wouldn't fit between the seats.
- A new sewer hose was cut to fit the motorhome's outside carrier compartment. I didn't measure it when I did it, but I believe that it was cut down from 10ft to 6ft. It's low priority at this point, but there's a lot of space behind there and I probably could upgrade the carrier and maybe install a second one?
As soon as I diagnose the reverse lights, I can get a piece of strip steel installed on the spare tire mount. If I drill the holes right and lengthen the spare tire's bolts, I can JB Weld Steel Stick them together. Then install a 90° angle at the top and mount the reverse camera to it. The camera has to be taller than my biggest bicycle on the hitch rack. And the hitch rack has an arm that extends about 30" up.
But in all actuality, I think I'd rather have it on more than just in reverse. So, I might wire it straight to the battery via a switch? One already exists in the cab for the lighter port power socket. That already supplies power to the three way splitter and the tablet which will connect to the camera via Bluetooth.
- Spare tire cover installed
The stock one was plastic with a wider outer diameter and it interfered with my hitch mounted bicycle rack.
- Frayed 12 gauge wire repaired temporarily
It's brown and I found out that was the main wire to my brake and running lights. I realized during the repair that I didn't have any extra 12 gauge wire. But I pulled it taunt enough to connect it with a blue cylinder.
- I purchased a laptop safe today, but in placing it in the motorhome, it ended up being larger than I wanted and wouldn't fit between the seats.
- A new sewer hose was cut to fit the motorhome's outside carrier compartment. I didn't measure it when I did it, but I believe that it was cut down from 10ft to 6ft. It's low priority at this point, but there's a lot of space behind there and I probably could upgrade the carrier and maybe install a second one?
As soon as I diagnose the reverse lights, I can get a piece of strip steel installed on the spare tire mount. If I drill the holes right and lengthen the spare tire's bolts, I can JB Weld Steel Stick them together. Then install a 90° angle at the top and mount the reverse camera to it. The camera has to be taller than my biggest bicycle on the hitch rack. And the hitch rack has an arm that extends about 30" up.
But in all actuality, I think I'd rather have it on more than just in reverse. So, I might wire it straight to the battery via a switch? One already exists in the cab for the lighter port power socket. That already supplies power to the three way splitter and the tablet which will connect to the camera via Bluetooth.
2015/03/29
Log 2015032901
Today, I moved several items to my relatives house and finally got my 3T jack over to my brothers. My 2008 Chevy HHR LS is only 1.55T, but the 2T jacks don't always lift it high enough for certain projects. My other 3T jack has an attachment with adjustable arms and pads that can lift two wheels off of the ground at once. When the tires need to be rotated on the HHR, they go back to front and front to back. And the only way to change them safely (that I know of) is either with a garage lift, or a jack with this attachment. The Chevy has limited places to lift it and the "T" attachment barely does the job.
The Cramper's shell, expandable floor and twin size memory foam mattress is also at a relatives house and need to be moved. But I discovered that the garage bay that I've been doing my recent automotive work is unoccupied. After I had my alignment and balances done on the wheels, I discovered that the HHR is still pulling to the left. Today, I discovered that isn't always true, which leads me to believe that the problem isn't the tension on the front brakes, but that one of the brake disc pads has come unseated and may need some replacement hardware.
That will give me some space and time to perform an electrical diagnostic on the rear tailgate release system. I have a theory on where it's problems might be. When I took out the backseats, there were several conduits running the top of the underside buckets. I may not have taken into account that the heavy gear that I load on top of it all might damage the wiring. And since the tailgate release motor isn't throwing fuses when activated, my guess is that I have a partially severed wire that is not making contact with any metal. And since electricity would be flowing along a diminished channel, it could turn the motor on, but not give it enough power to totally pop the tailgate.
To test that, what needs to be done first is an inline fuse of the right amperage would need to be crimped into wire of a similar gauge. One end would be attached directly to the battery's positive terminal, where the other would crimp into the electronic hand release pad. Then a temporary ground wire of similar gauge would have to be attached to the body and then to the release pad's negative wire. This is because you always power things up + then -. And the existing ground probably leads to the body (and not to the battery), it needs to be by-passed as well.
If the tailgate latch pops with the vigor that it should, then there is no doubt that I have a wiring problem elsewhere. If the tailgate release does not pop with such vigor, then wiring is bad between the release pad and the motor. I'm certain that it is not the motor or the pad because I had them both replaced with new units and the symptoms still persisted.
- My 1/2" socket driver is missing
The Cramper's shell, expandable floor and twin size memory foam mattress is also at a relatives house and need to be moved. But I discovered that the garage bay that I've been doing my recent automotive work is unoccupied. After I had my alignment and balances done on the wheels, I discovered that the HHR is still pulling to the left. Today, I discovered that isn't always true, which leads me to believe that the problem isn't the tension on the front brakes, but that one of the brake disc pads has come unseated and may need some replacement hardware.
That will give me some space and time to perform an electrical diagnostic on the rear tailgate release system. I have a theory on where it's problems might be. When I took out the backseats, there were several conduits running the top of the underside buckets. I may not have taken into account that the heavy gear that I load on top of it all might damage the wiring. And since the tailgate release motor isn't throwing fuses when activated, my guess is that I have a partially severed wire that is not making contact with any metal. And since electricity would be flowing along a diminished channel, it could turn the motor on, but not give it enough power to totally pop the tailgate.
To test that, what needs to be done first is an inline fuse of the right amperage would need to be crimped into wire of a similar gauge. One end would be attached directly to the battery's positive terminal, where the other would crimp into the electronic hand release pad. Then a temporary ground wire of similar gauge would have to be attached to the body and then to the release pad's negative wire. This is because you always power things up + then -. And the existing ground probably leads to the body (and not to the battery), it needs to be by-passed as well.
If the tailgate latch pops with the vigor that it should, then there is no doubt that I have a wiring problem elsewhere. If the tailgate release does not pop with such vigor, then wiring is bad between the release pad and the motor. I'm certain that it is not the motor or the pad because I had them both replaced with new units and the symptoms still persisted.
- My 1/2" socket driver is missing
2014/06/06
Log 2014060601
Last year, I did an adequate job wiring my 1195 Lb. Capacity Heavy Duty Folding Utility Trailer that I purchased from Harbor Freight Tools. But I left it's wires drooping in anticipation that I was going to fold it someday. Well, when I placed it in storage, while folding it, I taunt and stretched the wires. With all of the wire shorting problems that I've had between the trailer and car, I don't dare trust them again. So, the trailer needs to be rewired.
But I got to thinking this evening that there's no way to do this right when folding without having some kind of separation. Last year, I probably played around with using some kind of bullets. But as I understand, those are usually designed for wires typically used in model aircraft and small RC cars. I never found one that could interface to a 6 gauge battery cable so that my marine battery on the trailer could charge on the trailer while it's in motion.
So, what purchased today from Walmart in Mentor of Lake County are 5 - trailer extension wiring that have both a male and female ends for a 4 flat connection. I intend to use the first two at the midsection and the others at the trailer's taillights. That will give me the separation that I need. And the midsection connections should be rugged enough to stay connected and not accidentally ground to the frame.
Since my floor is wood, I also purchased some mounting brackets that one would use in a house to pin coaxial cable to a base board. I plan on tacking that up under the trailer to hold my wires so that they don't sag. The connectors at the taillights are there for diagnostic and by-pass purposes. If I'm down trail, I may not be readily able to diagnose, by-pass, or re-wire the main lines. With these new connectors, I can run a temporary by-pass on top of the floor and have full running lights in the meantime.
On a seperate note... I applied this year's sticker on the trailer's license plate today. The temporary by-pass lighting was mounted to the rear rails. But I discovered that the left turn signal wasn't working. I tested them two days ago and found that both worked. Therefore, there is a short in the car at the location where the hitch wiring was installed.
Leaving the Storage B, there wasn't any issues with the trailer linking up to the car or while driving. While at the gas station, they didn't have any alkaline AAA batteries, so I reluctantly purchased some lithium ion's instead. With the main taillights out, they were for a headlamp that I wrapped around one of the taillights that serves as the license plate light as well. The headlamp is for people who go in caves, or hikers. But it has an elastic band that I mounted to the taillight so it would illuminate the license plate.
But I got to thinking this evening that there's no way to do this right when folding without having some kind of separation. Last year, I probably played around with using some kind of bullets. But as I understand, those are usually designed for wires typically used in model aircraft and small RC cars. I never found one that could interface to a 6 gauge battery cable so that my marine battery on the trailer could charge on the trailer while it's in motion.
So, what purchased today from Walmart in Mentor of Lake County are 5 - trailer extension wiring that have both a male and female ends for a 4 flat connection. I intend to use the first two at the midsection and the others at the trailer's taillights. That will give me the separation that I need. And the midsection connections should be rugged enough to stay connected and not accidentally ground to the frame.
Since my floor is wood, I also purchased some mounting brackets that one would use in a house to pin coaxial cable to a base board. I plan on tacking that up under the trailer to hold my wires so that they don't sag. The connectors at the taillights are there for diagnostic and by-pass purposes. If I'm down trail, I may not be readily able to diagnose, by-pass, or re-wire the main lines. With these new connectors, I can run a temporary by-pass on top of the floor and have full running lights in the meantime.
On a seperate note... I applied this year's sticker on the trailer's license plate today. The temporary by-pass lighting was mounted to the rear rails. But I discovered that the left turn signal wasn't working. I tested them two days ago and found that both worked. Therefore, there is a short in the car at the location where the hitch wiring was installed.
Leaving the Storage B, there wasn't any issues with the trailer linking up to the car or while driving. While at the gas station, they didn't have any alkaline AAA batteries, so I reluctantly purchased some lithium ion's instead. With the main taillights out, they were for a headlamp that I wrapped around one of the taillights that serves as the license plate light as well. The headlamp is for people who go in caves, or hikers. But it has an elastic band that I mounted to the taillight so it would illuminate the license plate.
Location:
Home Port
2014/04/17
Log 2014041701
The wiring diagram for the turn signal switch which contains the headlight switch is in the Haynes Manual on page 12-25.
Subscribe to:
Posts (Atom)