This is the adventure and volunteerism log for Matthew Dexter Edmonds, aka "Treeman." Aside from Blogger comments, contact information is listed on Google+. And all places mentioned in this log are in the State of Ohio in United States of America unless otherwise stated. "The Wayne" = the Wayne NF.
Also, the motorhome mentioned is a 25ft, 1988 Itasca Sundancer, Model IF424RC with a Ford Econoline cutaway unless otherwise stated. It runs a 351 Windsor EFI V8 engine.
Search This Blog
2016/05/30
Log 2016053001
2015/03/13
Log 2015031201
At the moment, there's a pile of laundry on the floor that needs to get done and my old laptop tray on wheels needs to be taken out to storage. A message was sent to NiteRider requesting an electronic copy of their user guide for my Lumina 750 bicycle headlights. As of last week, I invested in a second unit that will mount opposite of the one already on there on the bicycle extension bars that I mounted. I'm looking forward to seeing how those two work in concert with the 250 lumen unit that I mount to my helmet. It also comes with a powerful rear taillight that I'm quite fond of and will match one that is already on there. They have a pretty powerful "pulsing" mode, that when set to alternate from each other, seems to send a pretty clear signal that I'm unusual and don't belong there, or there's something definitely artificial happening ahead.
- I'm unsure if the documentation for my Acer laptop is in my tablet's "library" folder? If it's not, I should download it to that directory in the event that it's needed when I'm off-line.
- And I still have yet to read my smartphone's manual. It may contain things that I don't know about it yet.
- Updated GIS/GPS files for the Buckeye Trail still need to be uploaded to the smartphone, tablet and laptop.
- I need to perform electrical diagnostics on my 2008 Chevy HHR's tailgate wiring. It just doesn't sound like it has enough power to pop the tailgate? If it were a short, it would be blowing fuses (and it's not) So, I think that I'm looking a wire that is partially breached, but not coming in contact with anything metal. With the backseats taken out, there are some harnesses that are exposed there and I think that the problem is probably there. But proper diagnostics dictate that I start with a multimeter at the plastic plug on the tailgate release motor and measure the amperage along the wire going towards the fuse block.
Another way that I can do is with the HHR's rear battery. Using an inline fuse, I can hard wire a positive lead to the corresponding wire just before and leading to the tailgate release's touch pad. If the motor promptly releases the latch, then my problem is elsewhere. If it doesn't, my problem is confined to the tailgate itself.
- Last week, I received a new truing stand for the bicycle's wheels. My previous one is still in good shape, but one of it's knobs fell off when it was getting stuffed into the trailer and I've been unable to find a replacement. This time, I need to procure some kind of tough container for it. If it's knobs do fall off, I don't want them to go very far, like some unknown mile on Interstate 77.
- two adjustable lanyards were purchased at Staples in Mentor of Lake County two days ago. I cut the mesh on one of them so that it only fits around my hand. That lanyard will also tie down the digital camera and keep it from falling out of my car windshield mount and hitting the floor.
I have about 40% of the intersection's photographed and geotagged for the Whipple Section - Buckeye Trail. And I have about 20% of it on video. The digital camera can geotag, but only if it's connected via Wi-Fi to the smartphone. The plan is to install a second goose neck windshield mount inside of my Chevy. Then use the digital camera to record the videos and the smartphone to take the geotagged photographs. I'm not so sure about the video, but the geotagged photos will be uploaded into the Google application Picasa, which will sense the geotags. From there, I'll use the option to upload them to Google Earth and incorporate them into my administration and maintenance folder for Whipple Section. Once done, I plan on giving a copy to the Trail Management Team and the Buckeye Trail Association's Headquarters for their records. Since their from various parts of the state, if they ever need to do anything on Whipple, they can study the sites that they're going to. As for me, I would like to study these myself on occasion.
2014/06/28
Log 2014062802
The DC jack on the Midland WR-100 is 12V and tip positive. I purchased a DC car power adapter for this unit today and confirm that it works. It will be replacing my former weatherband radio which did not tune well. This one is digital and performs better.
The bad news is that I don't know if a marine head unit would perform better? It would need to have its own GPS, or actively scan for the nearest station and interrupt whatever I'm listening to when a weather emergency occurs. I just haven't found a head unit like this.
Today, I purchased an eyelet to screw in to the tailgate latch plate that will route my paracord so that I have an easier manual release. Also, I purchased some silicone. The plan is to drill through the hull of the battery and spare tire compartment to run my trailer lighting cable out of the car so that I don't have to slam it in the tailgate door anymore. On the trailer hitch, I'll be installing a mount for it. I also purchased a small flashlight with a key ring small enough to to fit the loop hole on the HHR's manual tailgate release.
All of the trailer lighting connectors that I previously prepared for the tounge, separation point and lighting had to be replaced. I didn't keep track of the color coded wires that I snipped off and thought that they were irrelevant.
Earlier, I found a set of orange side marker lights that have and actual ground wire.
The drilling is going to require lifting the back end of the car up. The only way to safely do without a lift that on my Chevy HHR LS is to back it up on ramps. So, I got those out of storage today, as well as some hiking gear. Once I get The Cramper's equipment out of there, Storage B will be pretty thin.
Log 2014062801
I did my very best and I hope that this works for others. I just took off the rear interior shielding on my 2008 Chevy HHR LS. The picks shown are of the tailgate release. My screwdriver is on the manual release.
My smartphone was having trouble with the light levels in making these photos. The manual release is a metal piece with an eyelet that is mounted on the driver's side of the tailgate release mechanism. It pushes toward the rear of the car to release the tailgate and is spring loaded. The side of the eyelet has a place, a cut out specifically designed for a flathead screwdriver that when it makes contact, you can push the screwdriver against it and it should pop the gate.
I took the crash shielding off today because I was unable to find it myself with the owner's manual, Haynes, or by help of any Internet forum. Speaking strictly in theory, the eyelet should be barely large enough to get a very small key chain ring on it. I plan on boaring another eyelet to the back of the tailgate release plate. Route some paracord from on eyelet, then through and around the new one so the tailgate releases on a pull string.
My tailgate release seems weak. In warmer weather, it takes about 3 consecutive pushes if the button to pop. In the winter, sometimes it won't come up at all. It also has problems when I'm carring a heavy load in the back.
2014/06/16
Log 2014061601
I started using a butane torch today, but several minutes in, I remembed something about the stabilizer bar being made out of tempered steel and promptly quit. Yesterday, I purchased a drill bit extension from Lowe's in Mentor of Lake County. But to my chagrin, it only extends 3/8ths drill bits and I was very disappointed. With the Diablo blades on the Sawzall, I was able cut most of the hex off of the bolt. But because the blade was so wide, it left a sliver of the hex still on there. So, I mounted a metal cutting blade of standard width and was able to slice it off without damaging the stabilizer bar.
Afterwards, I took off the right fender. It was just a series of bolts. But to my chagrin, the after market replacement fender came with it's own eye socket wielded to it. Now, I have an extra. But the replacement didn't come with any insulation. I'm thinking that I might be able to reuse the one from the old fender. As for installing, I've decided that I'm going to "sleep on it." Considering the amount of bolts it and the under shielding has, I'm wondering if that is going to be a mistake?
I was about the bleed the left front caliper solo today, but didn't have a clear tube big enough to fit around the bleeding nut. And I'm concerned about no doing it right, so either I need a vacuum bleeding kit, or I should just task it out to the mechanic? I think I'm going to go with the latter. Because right now, I'm at a loss as to where the manual transaxle "check/fill" nut is. I think its to the left of the fuse block and has a hex key that is identical to the drain plug.
With all that being said, there'a bald spot on the table where I layout all of my new auto parts now.
2014/06/07
Log 2014060701
I repadded my cycling helmet today. And the SC Delco manual transaxle fluid for my car came in the mail today. Otherwise, I took my utility hauling trailer to my relatives house today and loaded up some yard waste, but with the license plate light still being out, it was too late to haul it to the recycler.
My automotive repair tasks have been prioritized. And I just started the list for the trailer rails upgrade. I found that the back door would have to be 48in tall to act as a ramp itself. That is unacceptable because it would be taller than the car and act as a wall when the caravan is in motion. I, instead, opted to build the rails to 3ft tall and install slots on the outsides so that they transport four ramps of 1" x 6" that are 6' long. They'll have slots on the back door and together, they should make a 6' ramp. The tool bay has wheels. And it's the heaviest thing that I transport. It's probably over 300lbs and is the hardest thing to load and unload. Last year, I avoided doing it at all costs.
I wanted to get some front bars mounted like you would see on the front of a police interceptor. If it's legal, I could mount a 5,000lb wench. My Chevy HHR and trailer are about 4,600lbs together and if I ever got stuck, I could just get myself out. But finding this for a car, and not a truck is difficult. So, these items are not essential to me at the moment are a "would be nice" item.
2013/07/19
2013/07/16
Log 2013071601
Tailgate latch won't pop. It's as if there isn't any power going to it. I looked at the relay in the fuse box, pulled it, but don't know how to inpect it yet.
Attempted manual release, but the only thing my screw driver caught was something plastic.
Drove to Headlands SP to try and bump it back in to functionality, but it hasn't worked. I'll probably have to craw back there again and have a look at the manual release compartment to see if I missed anything with a flashlight. Otherwise, I'll have to destroy that back sheilding to find something, then tie a longer cord to the manual release.
2013/07/15
Log 2013071501
This past week, gear was obtained from storage, which includes:
4L Water Bladder and drink tube
8GB Flash Drive
Two empty plastic containers
A small bottle of Febreze
A small bottle of water with approximately 8% Clorox Bleach
Sleeping bag compactor, size M
Blue jacketed speaker wire
Powered 7 port USB hub
Bluetooth wireless keyboard and trackball combination unit
75ft of outdoor extension cord
This week, the roof rack bag, music, cookware and laptop bags were all weatherproofed. The 40lb weight vest was also used this past week. So far, the repairs had little positive effect on the unit's performance and running with it is out of the question.
Months ago, I requested an offline PDF copy of the Haynes repair manual for my HHR. And from the reply email I received, I was under the impression that they have no desire to either make such a product, or even consider it. They have a web version, but its no good to me if I'm somewhere remote. I bring this up because the manual was stored in the laptop bag on the roof rack prior to the weatherproofing. This past week, I was able to use a blow dryer to dry out its pages and save it. The manual belongs in a pouch behind the driver's seat and I can place it there from now on. But what if I use it in the car, but my wet, sopping hands have to turn the pages when it's raining outside? I once considered taking a razor to its binding, then placing it's pages through an Automatic Document Feeder and making my PDF copy of it. But, I'm not sure that the wheels in scanner's ADF will handle it's newsprint pages without tearing it up? And now that it's damaged, I'd have to purchase a new manual to get it done.